Octave HP 500 SE

9,300 

The HP 500 has accompanied almost the entire OCTAVE story and thus shaped our company philosophy. For over 15 years, this preamp has stood for high sound consistency and state-of-the-art tube technology, whose top position would never have been possible without regular updates over such a long period of time—————————————

Giá cuong.audio: 9,300 USD

còn 1 hàng

Danh mục: , Từ khóa:
  • Mô tả
  • Đánh giá (0)

Mô tả

Basic model HP 500 SE Line
Special Edition Limited special model limited to 100 pieces
Tube fitting
Input stage: 1 x ECC 82; Output stage: 2 x EF 184 (Siemens D 3A)
design
Aluminum silver or aluminum black
Options
Phono MM / MC, HT Bypass

 

Technical specifications
Invi
Amplification Factor High (Gain High)
17.5 dB = 7.5
Invi
Amplification factor low (gain low) 9.5 dB = 3
Invi
Frequency range 3 Hz – 500 kHz 1.5 dB
Invi
Distortion factor 0.001% at 3V / 7.5 kOhm
Invi
Power supply: Gain high – 92 dB
Invi
External voltage gap Gain low -103 dB
Invi
Channel separation 65 dB 1 kHz
Invi
Interpreting input to input – 86 dB 10 kHz
Invi
Input resistor 100 k ohms
Invi
Output resistance 100 ohms (RCA); 2 x 50 Ohm XLR
Invi
Channel equalization via volume control 0.5 dB – 70 dB
Invi
Pinout XLR output Pin 1: ground, pin 2: + (not inverted), pin 3: – (inverted)
connections

Inputs: 5 x high level RCA

Optional inputs: 1 x Phono MM & 1 x Phono MC

Outputs: 2 x Cinch, 1 x XLR, 1 x Tape Rec

Features
Phono MM / MC, HT Bypass
Invi
Phono-MM
Invi
Input impedance
47 kOhm / 130 pF
Invi
sensitivity
3 mV
Invi
Tolerance RIAA equalization
0.3 dB 15 Hz – 20 kHz
Invi
Reinforcement 40 dB 1 kHz
Invi
External voltage range (rated) – 73 dB
Invi
Corner frequency Subsonic filter 20 Hz / – 3 dB
Invi
Phono MC
Invi
Input impedance
37-500 ohms
Invi
sensitivity
0.1 mV
Invi
Reinforcement
30 dB
Invi
External voltage range (rated) – 75 dB
Invi
Invi Download:
Manuals
Invi
General data
Invi
Power consumption
50 W
Invi
Pre-weight 10 kg
Invi
Weight power supply 4 kg
Invi
Dimensions Power supply (width x height x depth) 18 x 10 x 28 cm
Invi
included supply Power cable, remote control
Invi
Unit dimensions (in mm)
Invi
image
Invi
Invi
Features
Invi
How The HP 500 SE is equipped as standard with two RCA outputs and one XLR output.
How The XLR output is transformer balanced and galvanically isolated
How The HP 500 SE Phono has separate inputs for MM / MC
How Phono MM and MC can be retrofitted.
How Input impedance MC adjustable in wide range
How Soft start for heating, operating voltage and signal output; Thereby maximizing tube life and trouble-free switching on and off. The output is released after 4 minutes.
How The gain of the high-level stage can be switched in two stages
How Stand-by function for bridging multi-hour operating breaks
How External power supply with multiple shielded mains transformer and integrated mains filter
 

Frequency response:

Invi Invi
image
Invi Invi
Frequency response Line levels in position gain low and high Deviation
in the frequency range 20 Hz – 200 kHz: 0.1 dB
Invi Invi
 

Distortion factor kges:

Invi Invi
image
Total THD + noise of the line stage in the frequency range 20 Hz – 200 kHz.
The distortion factor is extremely low and constant up to 20 kHz
Invi Invi
 

FFT spectrum:

Invi Invi
image
Interference spectrum of the line stage at 5 V output voltage at 1 kHz. Clearly visible the falling upper shafts and the low noise level. There are no noise disturbances at 50 & 100 Hz.
Invi Invi
 

Phono RIAA curve:

Invi Invi
image
Frequency response of the phono stage with and without Subsonic filter

Đánh giá

Chưa có đánh giá nào. Thêm đánh giá